FabLab Kamp-Lintfort

User Tools

Site Tools

Trace: • fabac20_woche02 • fabac21_week_07 • fabac21_week_16 • installation
documentation:machines:epilogfusion

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
documentation:machines:epilogfusion [2021/01/12 10:29]
ferdi [Table] 		documentation:machines:epilogfusion [2021/04/09 14:42]
ferdi
Line 1: Line 1:
 ====== Epilog Laser Fusion M2 ====== ====== Epilog Laser Fusion M2 ======
  
-{{https://fablab.hochschule-rhein-waal.de/files/files/images/FabTools/Lasercutter/epilog-fusion-m2.jpg?400}}\\ Arbeitsbereich 40" x 28" (1016 x 711 mm)\\ Leistung: 60 Watt\\ [[https://www.epiloglaser.de/assets/downloads/manuals/fusion-manual-web.pdf|Bedienungsanleitung]] +{{https://fablab.hochschule-rhein-waal.de/files/files/images/FabTools/Lasercutter/epilog-fusion-m2.jpg?400}}\\ Arbeitsbereich 40" x 28" (1016 x 711 mm)\\ Leistung: 60 Watt\\ [[https://www.epiloglaser.de/assets/downloads/manuals/fusion-manual-web.pdf|Bedienungsanleitung]]\\ 
 +[[machines:maintenance:epilogfusion|Maintenance]]\\
 ===== Epilog Fusion - Workflow ===== ===== Epilog Fusion - Workflow =====
  
Line 50: Line 50:
  
 | Turn on the Filter                                  | Turn on the air Compressor                                   | | Turn on the Filter                                  | Turn on the air Compressor                                   |
-| {{:machines:epilogfusion:activate_filter.png?200}}  | {{ :machines:epilogfusion:activate_the_compressor.png?300}}  |+| {{:machines:epilogfusion:activate_filter.png?0x200}}  | {{ :machines:epilogfusion:activate_the_compressor.png?0x200}}  |
  
  
 === How to start the Job === === How to start the Job ===
-{{:machines:epilogfusion:start_the_job.png?400|}}+{{:machines:epilogfusion:start_the_job.png?400|}}\\
  
-  - Go to the **Job** function on the Control Panel. +  * Go to the **Job** function on the Control Panel.\\  
-  - Press the **Go** key to start or resume a job. +  * Press the **Go** key to start or resume a job.\\  
-  - Pressing the **Stop** key will stop the lens carriage and the laser beam will be shut off. +  * Pressing the **Stop** key will stop the lens carriage and the laser beam will be shut off.\\  
-  - Pressing the **Reset** key will move the carriage to its home position.+  * Pressing the **Reset** key will move the carriage to its home position.\\ 
  
-[[#overview|Back to Overview]] 
  
 ===== Cutting Settings ===== ===== Cutting Settings =====
Line 241: Line 240:
  
 [[#overview|Back to Overview]] [[#overview|Back to Overview]]
 +
 +===== Inkscape =====
 +In inkscape you have to make sure that your cutting lines are thinner than 0.0254 mm\\
 +Instead of File --> print, you should use the "Win32 vector print"-addon:\\
 +{{:machines:win32_vector_print.jpg?400|}}\\
 +or save as pdf and print the pdf from Acrobat reader.\\
  
 ===== Working with the Epilog Job Manager ===== ===== Working with the Epilog Job Manager =====
Line 340: Line 345:
  
 {{:machines:epilogfusion:whatsapp_image_2020-09-28_at_9.22.39_am_1_.jpg?400|}} {{:machines:epilogfusion:whatsapp_image_2020-09-28_at_9.22.39_am_1_.jpg?400|}}
 +
 +===== letztes mal Linse geputzt =====
 +29.3.2021 Markus\\
  
documentation/machines/epilogfusion.txt · Last modified: 2021/05/27 09:13 by markus

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki