This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
documentation:machines:fablasermini [2022/03/01 15:47] daniele |
documentation:machines:fablasermini [2022/03/01 16:09] daniele |
||
---|---|---|---|
Line 93: | Line 93: | ||
{{: | {{: | ||
+ | |||
+ | Once the mapping has been selected, Visicut shows a small menù where is possible to: | ||
+ | |||
+ | * select or deselect a specific area (selected areas will be considered for the job, not selected will be ignored) | ||
+ | * order the selections (the processing is from top to bottom) | ||
+ | * select the job type for each selection | ||
+ | |||
+ | It is important to note the available job types: | ||
+ | |||
+ | * cut | ||
+ | * mark | ||
+ | * engrave | ||
{{: | {{: | ||
+ | In our test we will makr the green writing and cut the rest, as you can see in the image below. | ||
{{: | {{: | ||
+ | |||
+ | After sorting up the selection it is necessary to input the laser settigns. | ||
+ | Those are defined per different kind of job and they are expressed in % from 1 to 100. | ||
+ | To note that here there is not PPI or laser frequency settings. | ||
+ | The settings shown below are used for 4mm poplar wood. | ||
{{: | {{: | ||
+ | After applying the settings is possible to click on the " | ||
+ | Once the GCode has been generated, it is possible to export the GCode from Visicut. | ||
{{: | {{: | ||
+ | It is important to note the GCode file must be saved with *.nc extension to be compatible with UGS Platform. | ||
{{: | {{: | ||
+ | |||
+ | UGS Platform is the software used to operate Fab Laser mini directly, and to launch GCodes. | ||
+ | The first step is to load the previously generated file into the sofware (see open button on top left). | ||
{{: | {{: | ||
+ | The is it necessary to connect to the machine by selecting the right serial port and a baud rate of 9600. | ||
+ | You should see the writings populating the console, as confirmation of a successful connection. | ||
{{: | {{: | ||
+ | |||
+ | |||
+ | Before starting the cut, it is necessary to turn on different accessories. | ||
+ | |||
+ | You can turn all the accessories on in one go, by using the foot switch located under the table where the machine stands. | ||
+ | |||
{{: | {{: | ||
+ | You can directly check the correct operation of the accessories. | ||
+ | The chiller has an alarm if the temperature is too high or something is blocking the flow of the water. | ||
{{: | {{: | ||
+ | |||
+ | The air filter must be set manually to the maximum power. | ||
+ | You can do that by pushing the filter button until the light becomes red. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | The air assist compressor will start automatically. You can check it by seeing it vibrate or if there is air coming out of the laser head. | ||
+ | If not please check if the compressor is connected to the electricy. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Once all these pre-check have been done is tome to operate directly with the machine. | ||
+ | First check the focus distance with the focus tool. | ||
+ | The distance between the laser head and the material should correspond to the focus tool as shown below. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | If it is not the case you can remove the air assist pipe, unlock and rotate the head until it reaches the right distance. | ||
+ | Once done you must lock again the head, and reconnect the air assist pipe. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Now you can move, freely by hand, the laser head to the bottom left of the desired laser stock. | ||
+ | The origin is in the bottom left, below is an example of the origin position in relation to the cut example. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Once the head has been positioned correctly, it is possible to close the lid. | ||
+ | |||
+ | To start the job in UGS Platform: | ||
+ | |||
+ | - Push the "Reset Zero" button | ||
+ | - Push the play button | ||
+ | |||
+ | {{: | ||
+ | |||